ISO 17123-1:2014

Courtesy: ISO 17123-1:2014

This is a list of published International Organization for Standardization (ISO) standards and other deliverables. For a complete and up-to-date list of all the ISO standards, see the ISO catalogue.

The standards are protected by copyright and most of them must be purchased. However, about 300 of the standards produced by ISO and IEC’s Joint Technical Committee 1 (JTC 1) have been made freely and publicly available

ISO 16000 – ISO 16999

  • ISO/TR 16015:2003 Geometrical product specifications (GPS) – Systematic errors and contributions to measurement uncertainty of length measurement due to thermal influences
  • ISO 16016:2016 Technical product documentation – Protection notices for restricting the use of documents and products
  • ISO 16020:2005 Steel for the reinforcement and prestressing of concrete – Vocabulary
  • ISO/IEC 16022:2006 Information technology – Automatic identification and data capture techniques – Data Matrix bar code symbology specification
  • ISO/IEC 16023:2000 Information technology – International symbology specification – MaxiCode
  • ISO 16032:2004 Acoustics – Measurement of sound pressure level from service equipment in buildings – Engineering method
  • ISO 16034:2002 Ophthalmic optics – Specifications for single-vision ready-to-wear near- vision spectacles
  • ISO 16039:2004 Road construction and maintenance equipment – Slipform pavers – Definitions and commercial specifications
  • ISO 16054:2000 Implants for surgery – Minimum data sets for surgical implants
  • ISO/TR 16056 Health informatics – Interoperability of telehealth systems and networksISO/TR 16056-1:2004 Part 1: Introduction and definitions
  • ISO/TR 16056-2:2004 Part 2: Real-time systems
  • ISO/TS 16058:2004 Health informatics – Interoperability of telelearning systems
  • ISO 16059:2007 Dentistry – Required elements for codification used in data exchange
  • ISO 16061:2015 Instrumentation for use in association with non-active surgical implants – General requirements
  • ISO 16063 Methods for the calibration of vibration and shock transducersISO 16063-1:1998 Part 1: Basic concepts
  • ISO 16063-11:1999 Part 11: Primary vibration calibration by laser interferometry
  • ISO 16063-12:2002 Part 12: Primary vibration calibration by the reciprocity method
  • ISO 16063-13:2001 Part 13: Primary shock calibration using laser interferometry
  • ISO 16063-15:2006 Part 15: Primary angular vibration calibration by laser interferometry
  • ISO 16063-16:2014 Part 16: Calibration by Earth’s gravitation
  • ISO 16063-17:2016 Part 17: Primary calibration by centrifuge
  • ISO 16063-21:2003 Part 21: Vibration calibration by comparison to a reference transducer
  • ISO 16063-22:2005 Part 22: Shock calibration by comparison to a reference transducer
  • ISO 16063-31:2009 Part 31: Testing of transverse vibration sensitivity
  • ISO 16063-32:2016 Part 32: Resonance testing – Testing the frequency and the phase response of accelerometers by means of shock excitation
  • ISO 16063-33:2017 Part 33: Testing of magnetic field sensitivity
  • ISO 16063-41:2011 Part 41: Calibration of laser vibrometers
  • ISO 16063-42:2014 Part 42: Calibration of seismometers with high accuracy using acceleration of gravity
  • ISO 16063-43:2015 Part 43: Calibration of accelerometers by model-based parameter identification
  • ISO 16063-45:2017 Part 45: In-situ calibration of transducers with built in calibration coil
  • ISO 16069:2004 Graphical symbols – Safety signs – Safety way guidance systems (SWGS)